Over the past 24 months, TÜV SÜD's experts have been guests at BLOBEL several times. On a test stand specially built for this purpose, automatic, manually insertable and manually rotatable models of the worldwide known BLOBEL containment systems proved their reliable leak tightness.

Following chapter 5.8 of the VDS guideline 2564-1, the TÜV testers confirmed that the refined, even more chemical-resistant and more flexible BLOBEL special seal meets all requirements and ensures safe retention of environmentally hazardous extinguishing media in the event of a emergency. TÜV-tested quality, Made in Germany.

The latest certificates can be downloaded from the individual models:

• Retention barrier BL/BST
• Retention barrier BL/BTL
• Retention barrier BL/BED
• Retention barrier BL/BDD
• Retention barrier BL/BED-PM
• Retention barrier BL/BDD-PM

Celebrations marking Blobel GmbH’s 25th anniversary had only just ended – along with the training courses held every year for the staff at our various representative offices – when things got into full swing again.

Next on the agenda was the Bavarian Beach Volleyball Championship – where Blobel was able to make an important sponsorship contribution by providing Blobel barriers to enclose the sand court. The idea for this was suggested by the managing committee of the organizing club: the DJK Augsburg Hochzoll e.V.

What made this event special was the venue: the tournament was to be held on Augsburg’s main square, right in front of the town hall.

The general conditions proved to be a real challenge:

• the cobblestones were not to be damaged
• the ground was uneven and had a noticeable slope
• building the court and stands had to be coordinated with the deliveries of sand
• the barriers framing the sand court had to keep many tons of sand in place
• dismantling the court and stands required as much coordination as their construction

And so a great deal of effort went into the planning, drawings and calculations. The choice fell on Blobel containment profiles and liquistop barriers. Work began on 23 July 2016. The modules were delivered by our manufacturing partner Müllers GmbH in Rohrenfels. First of all, our joint, four-man team of design engineers and fitters built up the enclosure at the designated location in order to precisely position the corner posts. Then most of the barriers had to be taken down again to enable a huge plastic sheet to be spread out across the entire area so that the trucks waiting in line could unload the sand onto it. A bulldozer was used to spread and compress the sand. The movement and weight of the sand made it necessary to provide additional support for the barriers lining the long sides of the court. The barriers went up step by step after each load of sand that had been spread, until the “sandpit” could be closed off. It was arduous and sweaty work in the blazing sun. The following day, the heat forced our second team to put in a late-night shift: the barriers had become so hot during the day that they warped the advertising banners, making it impossible to glue them to the barriers. Thanks to the personal commitment and active assistance of a number of hard-working relatives, that, too, was overcome. The court was now finally ready for play and the tournament could get underway.

We stayed on in the stands as spectators to cheer on the players and applaud their artistry. And of course we were delighted to receive praise from the event organizers for having successfully enclosed the volleyball court.

It was an interesting experience, one that enabled us to demonstrate the quality of our barriers in what was a rather unusual setting. This foray into the world of sport is a perfect example of our company motto: The right Blobel barrier for every situation!

Back at Blobel, we’re now back to providing individual solutions in the field of flood protection and containment systems.

Click on the picture to start the video (approx. 14 MB).

As the owner of BLOBEL Environmental Engineering LLC, Delaware, USA, Norbert Blobel coordinated and oversaw the installation of our biggest joint contract to date: a total of 94 fully automatic BLOBEL barriers (90 BDD-U-PM for loading ramps and 4 BED-PM), along with 16 semi-automatic barriers provided by the company GSB.

Unfortunately, he didn’t receive a kilometre allowance, which would have been really worthwhile, for there were days when he covered up to 15 kilometres moving between the various construction areas inside the huge Bayer HealthCare warehouse (600 x 182 metres) in Georgia. It’s just as well that he’s an active ultra marathon runner.

Installing the barriers took from May to September 2015 – and only minimally affected the ongoing logistical operations at this distribution centre.

BLOBEL Umwelttechnik GmbH acted as contractor for BLOBEL Environmental Engineering LLC, which in turn had been commissioned by ARCO Design/Build, Inc., USA. We were able to complete this enormous project on time and on budget. A superb achievement by everyone involved – from ‘BLOBEL Deutschland’ and ‘BLOBEL USA’.

Click on the photo to start the video (approx. 10 MB).

The 18th of March 2015 was an exciting day for the company staff and management at Blobel Umwelttechnik GmbH. A few days earlier, the European Flood Protection Association had delivered a test container and installed it in the construction hall, and had also set up the test stands in the hall. Now the time had come to conduct the actual testing of three Blobel flood protection systems.

Due for testing were a window barrier in Category 03 (Object Protection: Windows) and two slide-insert barriers without supports for manual montage in Category 01 (Object Protection: Gates). A divided version of the slide-insert barriers with a central support/double support post was also tested in Category L (Landscape Protection). In addition to the experts from the European Flood Protection Association, Blobel had also arranged for a TÜV Süd inspector to be present. Extensive documentation on the barriers was submitted prior to the testing.

Inside the association’s specially designed container are test stands of various dimensions, which provide the framework for the barrier tests. The barriers have to be assembled and locked into position inside the test stand under conditions simulating a real emergency – while the inspectors clock the time required to do so. Water is then pumped to a certain height into the space between the wall of the test stand and the barriers. At specified intervals, the inspectors measure and log any leakage to within a millilitre.

Aside from the time taken to assemble and dismantle the barriers, and the watertightness of the flood protection system, the evaluation process also takes into account the storage and transportation volumes of the barriers. The European Flood Protection Association allows for various leakage tolerances, ranging from Class 0 to Class 5.
A flood protection system designated as Class 0 shows no leakage, whereas a Class 1 system leaks up to half a litre per square metre per minute. Class 2 permits leakage of between half a litre and 1 litre. The leakage rate for Class 3 is between 1 and 5 litres. For Class 4, it is between 5 and 10 litres. Finally, Class 5 describes barriers that leak more than 10 litres per square metre per minute.

Test Results:

• In Category 01 (Object Protection: Gates), both flood barrier systems with no central support/double support post – BL362 HDS (200x50) and BL324 HAP-SB (200x50) – were rated as Class 1.
• In Category L (Landscape Protection), the Blobel barrier BL329 HAP-SB (150x80) with a central support/double support post was also rated as Class 1.
• Also in Category L, the Blobel flood protection system BL361 HDS (150x80) with a central support/double support post was rated as Class 2.
• SAnd in Category 03 (Object Protection: Windows), Blobel’s window barrier plate BL341 FAP-PR 1 was even rated as Class 0.

New inspection dates have already been set for other barrier types.

Click here to see more photos of the test …

The largest construction industry fair for the Pacific Region, Central America and the Caribbean was held for the 13th time in Colombia. It covers virtually everything, from civil and structural engineering, architecture, urban development and design to interior decoration and furniture.

BLOBEL was represented in Bogotá for the first time, at a shared Bavarian stand that was part of the German stand organised by the Chamber of Foreign Trade. We have been receiving more and more inquiries about flood barriers from this part of the world and are currently installing a number of BLOBEL containment barriers in Medellín – so the fair was a welcome opportunity to get better acquainted with this new market.

For six days, a steady flow of visitors streamed through the halls from 10 a.m. until 8 p.m. It was a long and busy week, but worth it for the remarkable interest shown and the high quality of the contacts made. We were able, for example, to hold promising technical discussions about our containment and flood protection systems with a good many engineers and staff members from various planning offices.

The expanded and renovated hall complex of the Mainfrankensäle in Veitshöchheim lies directly on the Main River – which of course makes flood protection an extremely important issue.

More than 10 BLOBEL flood barriers (BL/HDS model) are already in place to ensure that the many events held here – such as the televised carnival centrepiece ‘Fastnacht der Franken’ – and the visitors who attend them are not put at risk by flood water. Side supports for the flood barriers were fitted to single and double-leaf doors and to lift doors before the shell of the building was completed.

When these lateral supports were installed, there was no flooring to attach them to as the ground consisted merely of a layer of gravel. Special substructures of V2A stainless steel were therefore put into place, with floor brackets that would lie flush with the floors when these were finally laid down.

If it comes to an emergency, the special seal applied to the lowest barrier element inserted into the side supports will press down onto these floor brackets. Together with the floor brackets, the tightly locked closure elements and the U-shaped, stainless-steel side posts (also fitted with a special seal) thus form a watertight space that closes off on three sides in the event of flooding.

Image 1: Shell construction – If flooding is imminent, the flood barriers can be inserted by hand into the side supports. The vertical locking mechanism presses the barriers down onto the special sealing material applied below to form a watertight seal.

Image 2: The lateral guide rails were put in place before the flooring was laid down, so a substructure with stainless-steel floor brackets was needed that would later be flush with the surface of the floor and provide an optimum base onto which to compress the sealing material applied to the bottom barrier.

Download the article on the Mainfrankensäle from Architektur Premium.

The first national conference on the civil defence of São Paulo – 1. Conferência Estadual de Proteção e Defesa Civil de São Paulo – was held in Brazil on April 13 and 14. Representing BLOBEL at our company stand, which was equipped with two types of barriers, our Portuguese-language brochures and our trade fair film, was Silvia Kühl. She was able to talk to many of the conference participants, who showed considerable interest in our products. Demand for more information material was equally strong. It’s clear that the Brazilian civil defence experts were highly impressed by the design and quality of our barriers. Thanks to the new contacts made, our participation at two further trade fairs in Brazil was also discussed. We’re delighted with this positive response, and we thank Silvia for the competent support she provided.

The fact that people in Salzburg were able to take a relatively relaxed view of the flood situation in the spring of 2013 – and keep their feet dry as well – was due not least of all to the BLOBEL flood barriers, which provided effective protection in critical areas. Along the Elisabethkai promenade, for example, and in the city’s Josephiau district, passersby and local residents were able to gaze in amazement, with no risk to themselves or their property, at the mass of mud and water flowing past them down the River Salzach.

The trade fair in São Paulo was very well attended, and the same can be said of our booth. Once again, the focus of interest was primarily on flood protection, drawing visitors not only from São Paulo and surrounding areas, but also from further afield – in fact, some of the visitors who travelled from other federal states, such as from Manaus, capital of the state of Amazonas, had to cross up to two time zones to take part in the fair.

AThe Blobel stand was also able to welcome and advise interested parties from neighbouring Paraguay, Uruguay and Peru. What makes it worth our while to keep participating in this very costly and organisationally demanding trade show in Brazil are the promising contacts we make there.

We would like to extend a particularly warm welcome to Silvia Kühl, our newly acquired representante no Brasil, and look forward to a close and successful cooperation.

The dam that protects Kurtinig from the River Adige broke some years ago, with the result that parts of the village and the nearby town of Salurn fell victim to flooding. Flood simulation has now shown that the Bahntrasse could serve equally well as a dam if only the road’s underpass were not a perfect conduit for a mass of water to flood into the village.

This prompted the competent Province of Bolzano to take action. The eight-metre-wide underpass has been equipped with stationary side rails, and an additional vertical support post will be mounted when the time comes to assemble the barriers. Municipal road service workers have already practised installing and locking into place the 25 or so barrier sections, which are fitted with seals.

Conclusion: Thanks to the speed and ease with which they can be installed, BLOBEL barriers offer effective protection against flood water. The plan is to get neighbouring communities along the Bahnstrasse to follow suit, so that their underpasses also receive the same level of flood protection and thus safeguard the various localities.

This elegant and modern luxury-class hotel on the island of Sylt is spectacularly situated between the dunes, tideland, beach and the North Sea. To ensure that the elements “remain firmly outside” even when weather conditions are less than pleasant, BLOBEL barriers have been installed to protect sensitive areas against flooding.

The HDS barrier system is designed to seal off the salt-water wellness spa and connecting swim channel that form part of the 3,500-square-metre spa area, as well as the guest corridor and the various openings and passageways used, for example, as delivery entrances. Accesses to the basement are, in fact, safeguarded against flooding on all four sides – that is to say, all the way to the top.

In view of the increased stress that salt water and salty air place on materials, the U-shaped posts for the barriers are made not of the usual high-quality V2A steel but of V4A, a particularly resistant premium steel.

At the in-house contact fair organised by the Technikerschule Augsburg in March of this year, BLOBEL presented itself to the technical engineering students as an attractive regional employer. The fair brings together first-time employees and companies. We had a number of interesting conversations with enthusiastic young people, and we now look forward to receiving job applications from this year’s graduates.

Our newly-created training area: a hive of activity

Following our first training course for distributors back in July, the first in a series of training courses for technicians was held on 28 September for our team in Switzerland.

This training day was organised and conducted by Norbert Blobel Jr. and Sebastian Prestel. The morning consisted of theoretical lessons on the subject of Blobel barriers, followed by an afternoon of practical work in the showroom. Topics covered included special mechanical features, fully automatic barriers and the various types of switch cabinets. This gave participants an opportunity to practise setting up and adjusting barriers, troubleshoot faulty switching under the guidance of the instructors, and ask questions related to their daily work. At the end of the day, the many questions posed by the participants were compiled – along with the relevant answers – into a set of practical FAQs.

The high level of interest shown was more than ample confirmation that our current training options are exactly what distributors and technicians need. We’re convinced that their newly-acquired skills, along with the sound knowledge they already possess, will help to provide our colleagues with greater on-site competence and assurance – much to the benefit of our customers. Before leaving for home, the Swiss team were handed certificates of attendance hot off the press.

After a late arrival in Brazil because of technical problems with the flight to São Paulo, things really got going for Gabriele Blobel. As a “one-woman trade fair team”, and with the active support of her tried and tested translator, Frau Daniely, the company boss spent the next three days working under great pressure. For Norbert Blobel was unfortunately unable to travel to FIMAI as planned because he was needed at several construction sites on the other side of the world.

Nevertheless, everything went well: even the plasma TV that had been ordered especially to show our new trade fair film was quickly replaced after first being stolen. The assistance offered by locals, combined with an obviously effective sign language, ensured that the Blobel stand was soon fitted out with sample barriers. Dismantling the stand proved just as unproblematic thanks to the reliability and thoroughness of the helpers and the haulage company.
Although lots of people visited our stand on the first day, there weren’t many trade professionals among them. But this did provide us with ample opportunity to engage in casual conversation as a way of gearing up for the open, communicative and very friendly Brazilians.
The second day brought with it many interesting technical discussions. Our stand was also visited by a number of trade associations, who offered their help in establishing contacts. The third and last day proved to be a very lively one for us, with plenty of specific inquiries. All in all, we were delighted with our participation at the fair and attendance at the joint Bavarian stand. Our new trade fair film was very well received and attracted a lot of interest, and so we’ll be expanding and lengthening it for future use.

On the relaxation side, the programme once again included a feast for the Bavarian exhibitors, this time at a Brazilian steakhouse, where the waiters carry the meat to your table on skewers and slice it straight onto your plate. At the same time, we were able to broaden our horizons with regard to caipirinhas, which are drunk in numerous variations here in its country of origin. There’s the classic de Limão version, but also de Morango e Jabuticaba, de Caju, de Lichia, de Tangerina, Tropical …

 

The 17th BLOBEL Europe Meeting was held at our plant in Gersthofen on 6 July 2012.

Taking part in the sales training at the new BLOBEL training room on this hot July day were our business partners from Germany, Switzerland, Holland, Belgium, Italy, Denmark and Australia, who had gathered for an update on latest developments in containment systems and flood protection. Time constraints had already obliged our French business associates to attend a separate sales training session weeks earlier.

Based on the experience gained in previous projects, technical director and engineer Joachim Blobel and design engineer Sebastian Prestel did more than take a close look at the features and functionality of the new, fully automatic HWS-K retention barrier. Participants were also given the opportunity to try out the other fully automated models, so as to familiarise themselves with the specifics of the various barrier types – an essential prerequisite for those expected to conduct qualified sales meetings and consultations with interested parties and clients back home.

Of course the training session in Gersthofen also dealt with the somewhat “drier” topics of day-to-day business. These included the many directives and their varying requirements concerning tightness: DIN 19569-4, VdS 2564, Bavaria’s LGA test guidelines, FM approvals, Flood Protection Association ... Here at BLOBEL, we’ve summed up all these different permissible leakage levels into a clear overview for our distributors. All relevant aspects were explained and discussed in detail.

And finally, our export specialist, Elisabeth Wackerl, briefed participants on important changes concerning shipping.

Drastic changes in world trade: starting from 25 March 2013, the status “known consignor” will no longer be valid. Companies must update their certification in time if they wish to obtain the new required status of “approved known consignor” from Germany’s Federal Aviation Office (Luftfahrt-Bundesamt).

EU intra-Community exports to become more complicated: the current “proof of shipment” is to be replaced by “certification of entry”. Companies failing to provide the necessary documentation will face further taxation on their sales tax or value added tax.

The meeting naturally also provided the perfect setting for relaxed and personal conversations and shop talk. All in all, it was an intensive, informative and entertaining day that ended on a convivial note with an evening of food and drinks.

Sydney: Blobel barrier protects underground garage from flooding

An unexpected sight awaited the residents of the Moreton by the Park housing complex in Redfern, Australia, as they looked out of their windows on the morning of 8 March this year: the streets of this Sydney suburb were knee-deep in rainwater. And yet none of them had any cause to worry about their cars, the lift shafts or other sensitive fixtures in the building’s underground garage. Installed at the entrance to the garage more than a year previously, the BL/HWS-K Blobel flood barrier ahad – not for the first time – proved its reliability by automatically moving into position to prevent the basement level in this block of flats from flooding.

In fact, Blobel has installed six other barriers around Redfern Park – and at the entrance to the catacombs of Redfern Stadium – to safeguard against flooding.

BLOBEL at the fair
acqua alta alpina in Salzburg (8–10 March 2012)

This specialised trade fair provided an excellent opportunity for us to hold informative discussions with a good many qualified visitors and decision makers. We even offered advice to the representatives of a major Austrian client – the state of Salzburg – who visited our stand. Since the exhibitors at the fair included competitors, any visitors interested in checking out the quality of our flood protection solutions were able to judge for themselves by making a direct comparison with rival products.

The “European Flood Protection Association” (Europaverband Hochwasserschutz e. V.), founded in Munich on 4 May 2011, introduced itself to experts at the acqua alta trade fair in Hamburg last October. Eighteen companies from five European countries had unanimously voted in favour of founding an association to deal with issues that may affect those involved in flood protection. The proposal resulted, among other things, from an attempt by “numerous stakeholders” to dictate production and safety criteria – especially concerning mobile flood protection systems – to the manufacturers. The association intends to take action against such interference from outside. If the association’s statutes come into force, the current Europe-wide practice of establishing a flood protection system in the run-up to public tenders will also cease. According to the statutes: “Product neutrality in public and corporate tenders will lead flood protection back to the market economy, and it will no longer remain in the hands of small groups.” A research institute will be set up to deal with quality labels and to develop the association’s policy. BLOBEL Umwelttechnik is a member of the association.

Link: www.europaverband-hochwasserschutz.eu

BLOBEL has delivered a huge, 20-metre-long barrier with a retention height of 800 mm.

The seven sections were fitted under the supervision of engineer Sebastian Prestel, the designer of the barrier, to protect O’Riordan Street in Sydney (main contractor: Buildline Constructions, owner: SCP, Sydney Corporate Park). Even heavy rain and extremely limited working times – only at weekends and at night from 7 pm to 5 am – could not stop the successful completion of this project. The residents of SCP in Alexandria, NSW, will therefore be able to face the next flood with confidence.

BLOBEL barriers of this kind can, of course, be driven over by a lorry when they are not in operation. In Germany, only two of these models have been fitted so far – all the others have been delivered to Australia.